Print Page | Close Window

Rebound and preload clicks.

Printed From: rsvr.net Forums
Category: RSV / RSVR / FACTORY
Forum Name: Technical Chat
Forum Description: Any technical problems or useful advise for other owners, remember this is just advice posted here, if you make something go BANG in a big way don't take anyone to court about it.
URL: http://www.rsvr.net/forum_posts.asp?TID=30016
Printed Date: 27 Mar 2026 at 02:26
Software Version: Web Wiz Forums 12.07 - https://www.webwizforums.com


Topic: Rebound and preload clicks.
Posted By: Txm
Subject: Rebound and preload clicks.
Date Posted: 03 Sep 2023 at 15:44
Hi,

Just had new fork seas fitted on a 2007 factory.

I’ve tried to set up the suspension to match factory settings.

Problem is I am not getting any clicks from the rebound or compressions damping nuts.

The spring pre load nuts click as the manual suggests they should.

Any ideas please?



Replies:
Posted By: Spoonz
Date Posted: 03 Sep 2023 at 16:09
You sure you haven’t got your adjusters mixed up as the preload shouldn’t click There is no need to go anywhere near the compression circuit to change seals so hard to see how they could mess that up. 


Posted By: Txm
Date Posted: 03 Sep 2023 at 16:26
Hi,

Manual definitely says clicks?



Posted By: Spoonz
Date Posted: 03 Sep 2023 at 16:43
Originally posted by Txm Txm wrote:

Hi,

Manual definitely says clicks?


no clicks for preload just turns.  Are you turning the blue nuts, thinking they are the rebound and compression adjuster ? It’s the adjuster in the centre of the blue nuts, not the nut itself. 




Posted By: Txm
Date Posted: 03 Sep 2023 at 17:04
I think you’re spot on mate. In the manual I’ve got them confused with each other.

Thanks very much


Posted By: Txm
Date Posted: 03 Sep 2023 at 17:36
Just adjusted and all looks fine.

Only concern is I can pull the left blue nut up and down by 1mm or so, the right hand side doesn’t move at all.

Does this sound like something isn’t adjusted correctly on the left side?


Posted By: Spoonz
Date Posted: 03 Sep 2023 at 20:11
Originally posted by Txm Txm wrote:

Just adjusted and all looks fine.

Only concern is I can pull the left blue nut up and down by 1mm or so, the right hand side doesn’t move at all.

Does this sound like something isn’t adjusted correctly on the left side?

There is a nut that holds the preload adjuster into the cap. If that is not tight you will have play. But on mine I had a bit of play even when the nut was tight so I had to put a thin shim in there to take up the slack you will only know if you remove the top cap from the fork so I would just monitor it and make sure it’s not getting worse. 


Posted By: albrown001
Date Posted: 07 Sep 2023 at 19:11
http://www.visordown.com/reviews/road-test/road-test-rsv-r-factory-v-999s-v-f4-1000r" rel="nofollow - http://www.visordown.com/reviews/road-test/road-test-rsv-r-factory-v-999s-v-f4-1000r

I use these settings on my factory. Except with a fat bloke rear spring. Works for me Thumbs Up

If its good enough for Niall Mackenzie at Oulton Park its good enough for me...

Hope that helps 



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.07 - https://www.webwizforums.com
Copyright ©2001-2024 Web Wiz Ltd. - https://www.webwiz.net