rsvr.net Forums Homepage
Forum Home Forum Home > Tuono > General & Technical
  New Posts New Posts RSS Feed - Tuning airbleeds and trimpots
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Tuning airbleeds and trimpots

 Post Reply Post Reply
Author
Message
greenman1966 View Drop Down
Moto3 racer
Moto3 racer
Avatar

Joined: 06 Jul 2016
Location: New Zealand
Status: Offline
Points: 90
Post Options Post Options   Thanks (0) Thanks(0)   Quote greenman1966 Quote  Post ReplyReply Direct Link To This Post Topic: Tuning airbleeds and trimpots
    Posted: 02 Aug 2018 at 07:03
I'm about to throw my toys, is there a cheats method to tuning a Gen 1 tuono. I've downloaded various methods and it worked last time, but today. I just could not get my bike running correctly. I've got both a standard chip and a FR100 and neither is cooperating. At present the standard chip is in. Just to get it going.
Help me Obi-Wan 
Back to Top
legend88 View Drop Down
Premium Member
Premium Member
Avatar

Joined: 18 Aug 2013
Location: Newcastle
Status: Offline
Points: 5068
Post Options Post Options   Thanks (0) Thanks(0)   Quote legend88 Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2018 at 07:52
I think 12 O'clock for both trim pots is the recommended starting point but you really need to get the TB balanced properly. You are just a little too far away from AP is there anyone near you with the correct equipment?
Back to Top
greenman1966 View Drop Down
Moto3 racer
Moto3 racer
Avatar

Joined: 06 Jul 2016
Location: New Zealand
Status: Offline
Points: 90
Post Options Post Options   Thanks (0) Thanks(0)   Quote greenman1966 Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2018 at 09:02
got it now, trimpots at 12 o'clock to start with . I had forgotten the most important first step .. Thanks.
Ill continue this Saturday afternoon . 


Back to Top
Spoonz View Drop Down
Admins Group
Admins Group


Joined: 11 Feb 2008
Location: North Devon
Status: Offline
Points: 9592
Post Options Post Options   Thanks (0) Thanks(0)   Quote Spoonz Quote  Post ReplyReply Direct Link To This Post Posted: 02 Aug 2018 at 09:16
Set the bypass screw and leave them, adjust via trim pots in future. The bypass are set at the factory and generally left on a Gen1 unless Tb maintenance has been carried out.
 
But your still pissing in the wind to be honest. I've personally never had a Gen1 fuel correctly with trim pots at 12 o'clock. Why ?
 
Because the rear cylinder generally wants to run a bit richer than the front. My Gen1 has the rear cylinder trim pot at 2 o'clock for example. And the trim pots are sensitive enough that 1mm turn could equate to 1% CO.  So your chances of being accurate without a readout are almost 0.
Back to Top
greenman1966 View Drop Down
Moto3 racer
Moto3 racer
Avatar

Joined: 06 Jul 2016
Location: New Zealand
Status: Offline
Points: 90
Post Options Post Options   Thanks (0) Thanks(0)   Quote greenman1966 Quote  Post ReplyReply Direct Link To This Post Posted: 04 Aug 2018 at 08:07
bikes all tuned now and goes like a haunted sh*thouse . So what is the difference between the two maps ?

Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.00
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.063 seconds.