Print Page | Close Window

Shout out to Griff ATC calibration not working

Printed From: rsvr.net Forums
Category: V4 Tuono
Forum Name: V4 Tuono.
Forum Description: Anything connected to the new Aprilia Tuono models
URL: http://www.rsvr.net/forum_posts.asp?TID=26854
Printed Date: 16 Nov 2018 at 22:45
Software Version: Web Wiz Forums 12.00 - http://www.webwizforums.com


Topic: Shout out to Griff ATC calibration not working
Posted By: PaulFargo
Subject: Shout out to Griff ATC calibration not working
Date Posted: 13 Jun 2018 at 19:18
Just had new tyres fitted on 2017Tuono V4 and tried to run the traction control calibration.Just couldn't get it to work, even tried changing to Km/h to ride at 40km/h. No joy took it to the local dealer he tried no luck. He then connected to PAD's found no errors all sensors working updated to latest maps still won't work. Anybody got any more suggestions.



Replies:
Posted By: Spoonz
Date Posted: 13 Jun 2018 at 20:42
Did it say calibration failed or are you assuming it did because the TC is off ?


Posted By: PaulFargo
Date Posted: 13 Jun 2018 at 20:55
Fitted new tyres, went through the menus as in the manual, dash has      calibration in progress bottom left, traction control light on bottom right of dash. Set off riding 2nd gear 40 km/h no change. Must of done about 10iles in total know.LOL


Posted By: Spoonz
Date Posted: 13 Jun 2018 at 21:06
As i understand it after riding in calibration mode, you then have to turn off the ignition and then turn it on again and manually re select an atc mode and level to turn off the light.  I don't think the dash gives any kind of direct confirmation that it has calibrated but if it lets you select a mode after the off /on then it has calibrated.



Posted By: Spoonz
Date Posted: 13 Jun 2018 at 21:33
Check the encoder ring didn't get tweaked when you had the wheel out too. Like Abs rings they are highly sensitive to any run out.


Posted By: PaulFargo
Date Posted: 13 Jun 2018 at 21:41
 Dealer checked all the obvious culprits and said no errors from any sensors PADS not picking up any faults or errors. 


Posted By: PaulFargo
Date Posted: 13 Jun 2018 at 21:42
but I will check of there is any run out on the rings. Thanks


Posted By: Sabre
Date Posted: 14 Jun 2018 at 08:54
Hi 

Spoony asked if you switched it on and off again after the re-calibration. Did you do this? I re-calibrated mine after changing tyre sizes and rear sprocket size and it was a doddle.


-------------



Posted By: PaulFargo
Date Posted: 14 Jun 2018 at 09:17
When the calibration is done the warning ATC calibration on the dash is supposed to disappear, which it does not, I did try switching off and waiting after riding for about a minute at both 25mph and 40kmph, yes I even changed to km's to be more accurate.


Posted By: Spoonz
Date Posted: 14 Jun 2018 at 09:56
unless it's an odd tyre combo that is out of calibration range, I can only think that the sensor is not getting an accurate reading from the encoder ring etc. Might be worth wiping over the sensor as well as checking the ring itself.


Posted By: PaulFargo
Date Posted: 14 Jun 2018 at 10:01
Thanks Spoonz, did drop down a size on the rear to a 190 rosso corsa 2's, will give the sensors a wipe just incase, when I check the encoder ring for run out. It is a strange issue as traction control and abs work perfectly, and the dealer diagnostics reported no issues.



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.00 - http://www.webwizforums.com
Copyright ©2001-2018 Web Wiz Ltd. - https://www.webwiz.net