rsvr.net Forums Homepage
Forum Home Forum Home > RSV / RSVR / FACTORY > 'How To Guides'
  New Posts New Posts RSS Feed - LED Indicator Relay Safety Modification
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


LED Indicator Relay Safety Modification

 Post Reply Post Reply
Author
Message
amb67 View Drop Down
Moto GP Alien
Moto GP Alien
Avatar

Joined: 11 Feb 2008
Location: Marden in Kent
Status: Offline
Points: 769
Post Options Post Options   Thanks (0) Thanks(0)   Quote amb67 Quote  Post ReplyReply Direct Link To This Post Topic: LED Indicator Relay Safety Modification
    Posted: 17 Dec 2009 at 22:34
About 12 months ago my indicator relay packed up and my indicators refused to flash. I had already decided that I was going to replace my indicators at some point with LED units so I replaced my relay with one that was LED compatible.

That was when the troubles all started, the LED relay was absolutely silent in its operation, hence no audible indication (Pardon the pun) that my indicator was flashing.

Being a seasoned biker of some 20 years plus I am well versed in what happens when a rider forgets to cancel the indicator, sorry for the image but this happens quite a lot.



I did not want to become one of those statistics so I decided to make a minor modification to my indicator circuit, here goes:

Firstly I went to Maplins Electronics or you can use any good electrical shop, or even Flea Bay and I bought one of these.



Link to Maplins for relay Click Me

Buzzer specs are:
Type Voltage Impedance Frequency Output at 30 CM
12V 9 – 20V 480 Ohms 400 Hz 75 dB
Make sure you have some way of attaching it to the indicator circuit, it could be by Scotch Locks (Arggghhh!!) or by solder (Lovely!!).

Remove the front fairing to gain access to the wiring loom.



Unhook the LED indicator relay from its mount so that you can access the loom easily.



IMPORTANT!! If you have a diode in the indicator circuit then the buzzer must be fitted between the diode and the LED relay. If you add the buzzer to the circuit outside of this area it will not work correctly.

Best to attach the buzzer to the indicator loom as close to the relay as possible.

For those using Scotch Locks follow this:

Pop down to your local Auto store and buy yourself a soldering iron, some solder and a book on how to solder.

For all who do not know what a Scotch Lock connector is:



For those soldering follow this:

Strip back a piece of the insulation about 10mm on each wire.

Attach the wires as so:

Black wire on the buzzer connects to the blue/black at the LED relay connector.
Red wire on the buzzer connects to the green at the LED relay connector.

Just twist them on to the main loom for now.



Now test that when you indicate left and right that the buzzer sounds.

OK, if it works well than you need to solder the connections and make good the loom insulation.

If it doesn’t work then retrace your previous steps and make sure you have followed the instructions. If all is correct then reverse the electrical connections you just made, it may be that the manufacturer of the buzzer has connected the wires differently internally.

Locating the buzzer

I tried various methods and positions of locating the buzzer and decided upon this method and location (See images below). My reason for this was that the sound of the buzzer was distorted when it was connected to a hard surface, distorted even further when the vibrations from the engine were encountered.

Small cable tie threaded through the buzzer



Buzzer cable tied to the loom to avoid vibrations





You will need to decide what’s best for you on the location and connection method.

However, I would strongly recommend that you stay away from Scotch locks as it will inevitably end in grief somewhere along the line.

Rebuild the bike in reverse order and go for at least a 2 hour road test, tell the wife it’s mandatory. LOL

I know that a lot of you will be saying 'No fecking way am I fitting a buzzer' well that's your choice. All I can say is that a huge percentage of motorcycle accidents happen at junctions and many are caused by the rider leaving the indicator on.

Hope this helps save some lives!!




Blue ones are so much faster than black ones.
Back to Top
amb67 View Drop Down
Moto GP Alien
Moto GP Alien
Avatar

Joined: 11 Feb 2008
Location: Marden in Kent
Status: Offline
Points: 769
Post Options Post Options   Thanks (0) Thanks(0)   Quote amb67 Quote  Post ReplyReply Direct Link To This Post Posted: 17 Dec 2009 at 23:06
Update:

You can now get this on Ebay if the constant buzzes gets to you when indicating to turn at traffic lights etc....

Buy Me Here

Basically it adds in a delay of around 15 flashes before the buzzer starts sounding, you can also buy ones that you can amend the delay time.  Thumbs Up








Blue ones are so much faster than black ones.
Back to Top
fusebox View Drop Down
Admins Group
Admins Group
Avatar
Aprilia performance boss bloke

Joined: 11 Feb 2008
Location: the shop..again
Status: Offline
Points: 3083
Post Options Post Options   Thanks (0) Thanks(0)   Quote fusebox Quote  Post ReplyReply Direct Link To This Post Posted: 17 Dec 2009 at 23:23
awesome Al!!

i totally agree with the scotch lock ideal..they are wrong and should be binned at the first oppertunity!!

you the man!!

www.apriliaperformance.co.uk www.apriliaforum.co.uk
www.apriliaownersclub.co.uk
www.apriliaspareparts.co.uk
Back to Top
amb67 View Drop Down
Moto GP Alien
Moto GP Alien
Avatar

Joined: 11 Feb 2008
Location: Marden in Kent
Status: Offline
Points: 769
Post Options Post Options   Thanks (0) Thanks(0)   Quote amb67 Quote  Post ReplyReply Direct Link To This Post Posted: 17 Dec 2009 at 23:30
It scares me when I see riders leaving their indicators on whilst riding down the road, every bike should have to have some audible warning device fitted.  Confused




Blue ones are so much faster than black ones.
Back to Top
martuk View Drop Down
Premium Member
Premium Member
Avatar

Joined: 26 Mar 2012
Location: United Kingdom
Status: Offline
Points: 576
Post Options Post Options   Thanks (0) Thanks(0)   Quote martuk Quote  Post ReplyReply Direct Link To This Post Posted: 14 Apr 2012 at 09:06
Can you do this to a Gen2?
Back to Top
redratbike View Drop Down
Moderator Group
Moderator Group
Avatar
The Collector Messiah

Joined: 07 May 2008
Status: Offline
Points: 16147
Post Options Post Options   Thanks (0) Thanks(0)   Quote redratbike Quote  Post ReplyReply Direct Link To This Post Posted: 14 Apr 2012 at 17:15
Originally posted by martuk martuk wrote:

Can you do this to a Gen2?
yes..guy sells the kits on ebay pretty cheaply


www.apriliaperformance.co.uk
www.apriliaforum.co.uk
www.apriliaownersclub.co.uk
Back to Top
edelliott View Drop Down
Moto GP Alien
Moto GP Alien
Avatar
Chippy maker!

Joined: 26 May 2011
Location: UK
Status: Offline
Points: 1476
Post Options Post Options   Thanks (0) Thanks(0)   Quote edelliott Quote  Post ReplyReply Direct Link To This Post Posted: 14 Apr 2012 at 20:42
f**k
I take it that bloke did not live!
 
Where did you get the picture?
I somehow just got in the habit of checking my dash quite often!
So I never leave mine on
Forza Aprilia Racing
Http://www.forzaaprilaracing.co.uk


Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.03
Copyright ©2001-2019 Web Wiz Ltd.

This page was generated in 0.063 seconds.